MTU.Community


Go Back   MTU.Community > Search Forums
Reload this Page Search Results
FAQ Calendar Today's Posts

Showing results 1 to 9 of 9
Search took 0.48 seconds; generated 89 minute(s) ago. Search: Posts Made By: dott1
Forum: Microstudio Help December 28th, 2002, 09:55 PM
Replies: 31
Views: 24,836
Posted By dott1
well it looks like it was the media, i tried with...

well it looks like it was the media, i tried with imitation and digital research and both failed, so i tried a hp disk and success twice. yeah finally, that was pretty frustrating. thanks for...
Forum: Microstudio Help December 28th, 2002, 04:46 PM
Replies: 31
Views: 24,836
Posted By dott1
firmware version 1.0f

firmware version 1.0f
Forum: Microstudio Help December 28th, 2002, 04:39 PM
Replies: 31
Views: 24,836
Posted By dott1
what is a firmware version everything was...

what is a firmware version
everything was correct, except there wasn't a box for dma on the hp drive, just the cd rom drive which doesn't read cdg
Forum: Microstudio Help December 28th, 2002, 04:17 PM
Replies: 31
Views: 24,836
Posted By dott1
i have already downloaded the lastest mtu...

i have already downloaded the lastest mtu drivers.
i changed to digital research technologies disks
the disk i burned plays through part of the disk and then locks up
i am going to try again
but this...
Forum: Microstudio Help December 28th, 2002, 03:49 PM
Replies: 31
Views: 24,836
Posted By dott1
i did what you said and i put a different brand...

i did what you said and i put a different brand of disk in and it finally began to write and then i got the same error message when it was 94 % done. help!
Forum: Microstudio Help December 28th, 2002, 03:14 PM
Replies: 31
Views: 24,836
Posted By dott1
WNASPI9X: WNASPI9X: V1.13 WNASPI9X: ...

WNASPI9X:

WNASPI9X: V1.13

WNASPI9X: DCB=0xCB91E7D0 Port=ESDI_506 Bus=0 Hba=1 Target=0 Lun=0 Dev=5 Drv=4

WNASPI9X: DCB=0xCB91C3C0 Port=ESDI_506 Bus=0 Hba=1 Target=1 Lun=0 Dev=0...
Forum: Microstudio Help December 28th, 2002, 03:06 PM
Replies: 31
Views: 24,836
Posted By dott1
i am using microstudio i have an hp write speed...

i am using microstudio
i have an hp write speed of 4x
i am using imitation disk that don't say their write speed, but i think it is 8x
Forum: Microstudio Help December 28th, 2002, 02:59 PM
Replies: 31
Views: 24,836
Posted By dott1
i had already done that. i used the aspi checker...

i had already done that. i used the aspi checker and everything seems fine.
i am writing at 1x speed
Forum: Microstudio Help December 28th, 2002, 02:00 PM
Replies: 31
Views: 24,836
Posted By dott1
Angry error write command failed

I have tried everything to burn a cd from the hard drive. I did it a long time ago, so I know it is possible. Recently I had to reinstall the software and now I just can't get it to write a cd.
I...
Showing results 1 to 9 of 9

 

All times are GMT -4. The time now is 04:38 PM.

Contact Us - MTU.com website - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2025, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.