MTU.Community


Go Back   MTU.Community > Singers & Hosts Wisdom

Singers & Hosts Wisdom Post how to be a great karaoke singer or host.

Reply
 
Thread Tools Display Modes
  #21  
Old July 28th, 2012, 09:28 AM
Roy Dennis's Avatar
Roy Dennis Roy Dennis is offline
Super Moderator
 
Join Date: Mar 2004
Location: Kent, England
Posts: 6,343
Re: QSC Speaker Problem...

Just an idea if you don't mind drilling a hole in your speaker pole.

If you were to screw a # 8 self tapping pan headed screw into the pole just above were the bottom of the speaker would come, you could adjust how tight the speaker fitted by adjusting how tight the screw was inserted into the pole.
If there was enough room between the speaker hole and the pole you could have 2 or 3 screws spaced around the pole.

Another option might work Get a thin rubber O ring, place on the pole then push the speaker over that for a tight fit, you would have to find the best size O ring but these could easily be removed from the poles without leaving a sticky residue.
__________________
Roy.
Test Laptop: Windows 10 Home Premium 64bit. Acer Aspire 5738G Intel core 2 Duo T6600 ATI Graphics 500Mb dedicated. 4Gb Memory 500 Gb SSD Drive. K-lite Mega version 1205
Show Backup: Windows 10 Acer Aspire Touch Screen V15, Intel core i5, Iris Graphics 6100 up to 8277mb dynamic video, 16Gb memory, 1 TB hybrid HDD. K-lite Mega pac.
Show Computer: Windows 10, Dell Inspiron 15 7000, CPU I7-855OU, Ram 8GB, Graphics UHD620 + Nvidea GeForce 940MX, Hard Drive SSD 256GB + 1GB internal.

Last edited by Roy Dennis; July 28th, 2012 at 09:56 AM.
Reply With Quote
  #22  
Old July 28th, 2012, 07:02 PM
WaltR WaltR is offline
VIP
 
Join Date: Oct 2004
Location: Beverly Hills, Florida
Posts: 3,156
Re: QSC Speaker Problem...

Are your speaker flanges readily removable, maybe 3 or 4 screws? If so you can buy new flanges where you purchased the adapters. Just a thought.

Walt
Reply With Quote
  #23  
Old July 30th, 2012, 01:36 AM
kod kod is offline
Registered User
 
Join Date: Mar 2010
Location: North Carolina
Posts: 1,583
Re: QSC Speaker Problem...

Quote:
Just an idea if you don't mind drilling a hole in your speaker pole.

If you were to screw a # 8 self tapping pan headed screw into the pole just above were the bottom of the speaker would come, you could adjust how tight the speaker fitted by adjusting how tight the screw was inserted into the pole.
If there was enough room between the speaker hole and the pole you could have 2 or 3 screws spaced around the pole.

Another option might work Get a thin rubber O ring, place on the pole then push the speaker over that for a tight fit, you would have to find the best size O ring but these could easily be removed from the poles without leaving a sticky residue.
Roy,

I like the idea of using screws. I may even try using pop rivets as they just might stick out enough to increase the size of the pole just enough to make the speaker fit more snug...

Thanks for the idea...

Quote:
Are your speaker flanges readily removable, maybe 3 or 4 screws? If so you can buy new flanges where you purchased the adapters. Just a thought.
Walt
Walt,

QSC speakers have a flange that rotates to allow the speaker to sit straight up or be rotated 180 degrees to allow the speaker to tilt 7 1/2 degrees...

I am reluctant to defeat this option...
__________________
KOD
Reply With Quote
  #24  
Old August 14th, 2012, 03:19 PM
BooBoo BooBoo is offline
Registered User
 
Join Date: Nov 2003
Location: Louisville, KY
Posts: 89
Re: QSC Speaker Problem...

Line the inside of the speaker hole with electrical tape. Leave a 1\4 to 1\2 inch outside the hole and wrap it under the speaker cab as a flange so it doesn't get bunched up inside. The tape should provide a less slick surface than the metal and should hold the cab without it being too tight. Don't fix the pole, fix the hole.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -4. The time now is 12:55 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2024, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.