MTU.Community


Go Back   MTU.Community > Microeditor Software > Microeditor Help - Versions 5.0-5.5

Microeditor Help - Versions 5.0-5.5 Discussions for Microeditor versions that use Krystal DSP Engine audio card

Reply
 
Thread Tools Display Modes
  #1  
Old June 20th, 2002, 04:25 AM
arminroesch arminroesch is offline
Registered User
 
Join Date: Nov 2000
Location: Deitingen, Switzerland
Posts: 24
Question new version MTUMSND.VXD

During installation and after that at start of MICROEDITOR 5.5 I am getting the message "you need a new Version of MTUMSND.VXD". Then it terminates.

Where can I get one?

Regards

Armin
__________________
Roesch Electro Acoustic
Deitingen
Switzerland
Reply With Quote
  #2  
Old June 20th, 2002, 01:20 PM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Armin,
What you need to do is just reboot the computer once the install is done. This should then allow it to open no problems.

Let me know what you find.
__________________
Bryan, MTU
Reply With Quote
  #3  
Old June 20th, 2002, 02:54 PM
arminroesch arminroesch is offline
Registered User
 
Join Date: Nov 2000
Location: Deitingen, Switzerland
Posts: 24
Question

Bryan,

Thanks for reply.
I am still getting the same message. Then a window open "can't access MicrosoundDevice".

I let 5.4 installed and this version runs OK. May that be the reason?

Armin
__________________
Roesch Electro Acoustic
Deitingen
Switzerland
Reply With Quote
  #4  
Old June 20th, 2002, 03:20 PM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Armin,
What version of Windows are you running? If you are trying to install 5.5, you need to uninstall 5.4, reboot, install 5.5, reboot. Then it should run ok, once you have rebooted.

Let me know what you find.
__________________
Bryan, MTU
Reply With Quote
  #5  
Old June 21st, 2002, 09:59 AM
arminroesch arminroesch is offline
Registered User
 
Join Date: Nov 2000
Location: Deitingen, Switzerland
Posts: 24
Question

Bryan,

Thanks for help.
I am using win98se.
After deinstalling 5.4 and 5.5 and reboot.
Installing 5.5 I am getting still the same message.

Even during deinstallation of 5.5 the message appears.

Armin
__________________
Roesch Electro Acoustic
Deitingen
Switzerland
Reply With Quote
  #6  
Old June 27th, 2002, 12:52 PM
arminroesch arminroesch is offline
Registered User
 
Join Date: Nov 2000
Location: Deitingen, Switzerland
Posts: 24
Unhappy What now?

Bryan,

Today I got the confirmation from my creditcard company that you charged for upgrade 5.4 to 5.5

Until today I could not brought it to run.

So I needed to reinstall my previous version 5.4

I hope you can find the reason why 5.5 does not run as written in my last post.

Armin
__________________
Roesch Electro Acoustic
Deitingen
Switzerland
Reply With Quote
  #7  
Old June 27th, 2002, 02:30 PM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Armin,
I have found out what the problem is. The version 5.5 will not run under Windows 98. This version will only work under XP or 2000, so there is no way to make it run, as of now. I will get this fixed as fast as I can. I will then contact you about getting the new version to you.

Thanks,
Bryan Cox
MTU
__________________
Bryan, MTU
Reply With Quote
  #8  
Old October 15th, 2002, 08:06 AM
arminroesch arminroesch is offline
Registered User
 
Join Date: Nov 2000
Location: Deitingen, Switzerland
Posts: 24
Question MicroEditor5.5 for WIN98?

Dear Bryan,
I think that WIN98se is no more a task for MTU because you did not send me any information about ME5.5 for WIN98.

I would like to use the new possibilities in 5.5 I am now planning upgrade of my current system to XP.

I have MicroCD 2.4.0.0 and MicroTools 2.0a. Do these programms run under XP?

My current system is formatted with PartionMagic. Do I need PartionMagic in XP too?

Currently I would like to stay with WIN98! (Never change a running system..) But when MTU does not deliver 5.5 for it I have to upgrade...

Thanks
Armin
__________________
Roesch Electro Acoustic
Deitingen
Switzerland
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 01:27 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2024, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.