MTU.Community


Go Back   MTU.Community > KPro Studio and KHPro Software - Create your Own Karaoke Songs > KPro Studio and KHPro Help

KPro Studio and KHPro Help Post KPro Studio and KHPro questions, tips and suggestions here.

Reply
 
Thread Tools Display Modes
  #1  
Old February 19th, 2003, 11:52 AM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
Problem> Linksys USB & KProID.exe

1. Download Kpro 4.0 and KproID.exe.
2. Purchased recommended USB Linksys EtherFast 10/100 Compact USB Network Adapter.
3. Installed USB Device in USB Port.
4. Win98Se said found new hardware.
5. Directed to CD rom to install drivers.
6. Appeared Drivers installed.
7. Got command to put in Win98 CD.
8. Looks like some drivers were installed from Win98 CD.
9. Re-started Computer.
10. In My Computer, under NETWORK ADAPTERS, HAVE AN EXPLAINATION MARK BY THE USB ETHERNET CARD.
11. When I click on update drivers and direct to CD rom, says best drivers already installed.
12. When I run KproID.exe, no devices found.

13. ANY IDEAS OUT THERE?

P.S. Since I installed the USB Ethernet Device, my Fireware BlackIce isn't working, have had to temp disable.

Last edited by kjzone; February 19th, 2003 at 01:13 PM.
Reply With Quote
  #2  
Old February 19th, 2003, 12:05 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
KJZONE

Don't know if your answer is here or not, but went to the LINKSYS website and found this support page which talks about downloading driver for the product. May be worth a shot.


http://www.linksys.com/support/support.asp?spid=24

Take care,

George

Reply With Quote
  #3  
Old February 19th, 2003, 12:11 PM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
George.....thanks.....but that didn't work either.
Said, best driver already installed.

Kjzone
Reply With Quote
  #4  
Old February 19th, 2003, 12:25 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
When you go in through the device manager and check properties does it say the device is or isn't working properly?
Just brainstorming.

George
Reply With Quote
  #5  
Old February 19th, 2003, 12:31 PM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
George..........
Per suggestion of LinkSys Help.......

1. Went to Windows Help and looked up ASD.
2. Ran ASD
3. Re-Started Computer
4. Device Manager NOW shows USB Ethernet Device is install properly.

5. BUT when I run KproID.exe, says no Device Present.
Reply With Quote
  #6  
Old February 19th, 2003, 01:00 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
Beats the heck out of me.
Reply With Quote
  #7  
Old February 19th, 2003, 11:06 PM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
George........finally got it working.

1. Even though the device manager said the USB Ethernet was installed, it is ONLY the Device's Driver, you have to "CONFIGURE" THE USB ETHERNET DEVICE.

2. Had to go to the Control Panel, Network Icon.
3. Had to Click on USB Ethernet and "Add"
4. Then had to "add" Microsoft Netware Networks.
5. Then had to "add" USB Ethernet Dial-Up Adapter.
6. Then had to "add" USB Ethernet TCP/IP Adapter.
7. Then called for certain Win98 CD Rom Files.
8. Then re-booted the Computer.
9. Ran KProID.exe and it now found the USB Ethernet Device (MACID) code.
10. Sent request to MTU for Serial Number.

Last edited by kjzone; February 20th, 2003 at 08:19 AM.
Reply With Quote
  #8  
Old February 19th, 2003, 11:11 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
Great, will have to try to remember this thread. It'll surface again with someone else. Thanks for the info.

George
Reply With Quote
  #9  
Old February 20th, 2003, 10:02 AM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
KJzone,
Glad you got it working. I was going to post this out here from your email to me, but you have already posted it.
__________________
Bryan, MTU
Reply With Quote
  #10  
Old February 20th, 2003, 10:45 AM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
FOLLOW-UP.......

1. Just got my serial number for my macid address from Doug at MTU.

2. Program installed correctly.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 05:02 PM.


Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2024, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.