MTU.Community


Go Back   MTU.Community > Microstudio Software & Burners > Microstudio Help

Microstudio Help Post Microstudio questions, tips and suggestions here.

Reply
 
Thread Tools Display Modes
  #21  
Old June 17th, 2005, 03:52 PM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
I still have not yet seen a version, for myself to test yet. This was pushed back a little bit, as the Microstudio code was much more difficult to remove the Old, that is tied to the ASPI drivers and replace it with the new.

I am not sure as to when this should be ready for testing.
__________________
Bryan, MTU
Reply With Quote
  #22  
Old September 2nd, 2005, 03:03 PM
wmharrison wmharrison is offline
Registered User
 
Join Date: Aug 2005
Location: st louis
Posts: 15
Question after demo download, microstudio wont open

i have had microstudio for a couple of years now and it has always worked well. i recently tried to download the "HOSTER" demo from mtu.com and now i cant open my microstudio.

i am not too computer literate, so please, any assistance would be very much appreciated.
Reply With Quote
  #23  
Old September 2nd, 2005, 03:26 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
Try re-installing Microstudio. This generally takes care of it .

George
Reply With Quote
  #24  
Old September 2nd, 2005, 06:48 PM
wmharrison wmharrison is offline
Registered User
 
Join Date: Aug 2005
Location: st louis
Posts: 15
thanks
Reply With Quote
  #25  
Old September 5th, 2005, 03:01 PM
wmharrison wmharrison is offline
Registered User
 
Join Date: Aug 2005
Location: st louis
Posts: 15
i found my disc with the microstudio on it, but i can not find the password that will let me install it.

any ideas?
Reply With Quote
  #26  
Old September 5th, 2005, 03:52 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
The registration code is in the download email you received. Hope you saved it.

George
Reply With Quote
  #27  
Old September 5th, 2005, 04:53 PM
wmharrison wmharrison is offline
Registered User
 
Join Date: Aug 2005
Location: st louis
Posts: 15
i cant find it. any way around this?
Reply With Quote
  #28  
Old September 5th, 2005, 05:53 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
Go to your MTU folder(normally c:\Program files\Micro Technology Unlimited) and locate the Microstudio installation file. I don't know which version of Microstudio you have, but the last version installation file would be mstudio2611setup.exe

An older version may be worded different, but would still contain a Microstudio reference and end in .exe

Double click it and see if the install shield gives you the option to install UPGRADE, (or REPAIR in an older version). You shouldn't have to enter a registration code if that is there. If it calls for one, you won't be able to install without it, but you won't be any worse off than you are.

George
Reply With Quote
  #29  
Old September 6th, 2005, 02:23 PM
wmharrison wmharrison is offline
Registered User
 
Join Date: Aug 2005
Location: st louis
Posts: 15
thanks george, you have been very helpful. my microstudio is up and running again.

i do have another question though.
as i said before, i'm not too computer knowlege ful.
the microstudio disc that i have is an old one i guess. it has microstudio v2.315 on it. it also has vogone v2.014 and karaoke home producer v2.009 and keyrite v1.202. i have never used anything but the microstudio, but i would like to upgrade to the latest versions of all of these.
do i just purchase the latest versions? or do i have to purchase all the versions that came between?

again, any help would be much appreciated.

rick
Reply With Quote
  #30  
Old September 6th, 2005, 03:05 PM
George George is offline
Registered User
 
Join Date: Jun 2001
Posts: 5,299
Rick,

Glad you're up and running.

To get the latest versions, I believe all you would need do is puchase the latest upgrades for each product you desire to upgrade.


Take care,
George
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 06:28 AM.


Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2024, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.