MTU.Community


Go Back   MTU.Community > Microstudio Software & Burners > CD-Recorders and Media Open Forum

CD-Recorders and Media Open Forum All about drives and media

Reply
 
Thread Tools Display Modes
  #1  
Old March 4th, 2003, 09:16 AM
Glenski3 Glenski3 is offline
Registered User
 
Join Date: Aug 2001
Location: United Kingdom
Posts: 23
Sony CD-RW Problems

Can anybody help!

I have a Sony CD-RW CRX200E ATAPI Drive which does support CD+G...

I have now purchased a Sony CD-RW CRX220A1 Drive which does not support CD+G...

The problem I have Is that I want to run both CD-RW Units in my PC...

The CRX200E Is setup as the Master (IDE Secondary)
The CRX 220A1 Is setup as the Slave (IDE Secondary)

But when I come to reboot the PC It holts at the 'Verifying DMI Pool Data' and the whole PC freezes...

I have tried both drives around the other way regards Master/Slave... The settings in BIOS are set to Auto Detect!

Previously I had a standard Matsumi CD-Rom Drive running alongside the Sony CRX200E In harmony, with no problems...

It seems to me that both the Sony drives are In conflict with each other!!

Does anybody know what I'm doing wrong?

All cables are connected fine...
Is there something I need to do In setup?

Please help!

Cheers

Glenski
Reply With Quote
  #2  
Old March 4th, 2003, 09:48 AM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
First check you computer ribbon cable to see if it's a:

1. Standard Ribbon Cable with 40 Pin Connections or

2. If it's a Cable Select [CSEL] with only 39 Pin Connections (one of the 40 Pin Connections is "blocked" toward the middle of the connector)

3. If it's a Standard Ribbon Cable make sure that the Jumper Connections on the Back of the CD-RW's are set correctly, one to Master and one to Slave.

4. If you have a "Cable Select" Ribbon, then the Jumper Connections on the Back of the CD-RW's are both set to "CSEL" Cable Select. To use "CSEL" your computer's bios MUST support CSEL.

5. I believe that "auto detect" implies you have jumpers set on CSEL and a 39 Pin CSEL Ribbon Cable.

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

6. P.S. If you plan to "Copy on the Fly", suggest one CD-RW be on the Primary ribbon cable and one CD-RW be on the Secondary Ribbon Cable.
Reply With Quote
  #3  
Old March 4th, 2003, 09:49 AM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Glenski,
I would contact Sony, this sounds like some type of hardware issue with their drive. You are correct in that the drives should work correctly together.
__________________
Bryan, MTU
Reply With Quote
  #4  
Old March 4th, 2003, 10:07 AM
Glenski3 Glenski3 is offline
Registered User
 
Join Date: Aug 2001
Location: United Kingdom
Posts: 23
Thanx

Thanx KJZone

I have indeed done all that you have listed... but still it does not work...

The ribbon cable is a full 40 pin connector, regards the Auto Detect... Imeant auto detect for the CD-RW Drives on boot up...

As MTU Support states.. I will try and contact Sony!

Maybe it's something to do with the settings in BIOS...

I'll see what happens....

Bloody shame that the Sony CRX220A1 does not support CD+G... It's a bloody fast drive 52X/24X/52X

Cheers guys

Glenski
Reply With Quote
  #5  
Old March 4th, 2003, 10:13 AM
kjzone's Avatar
kjzone kjzone is offline
Frequent Member
 
Join Date: May 2002
Location: Silver Spirng, Maryland 20906
Posts: 346
I edited my original Post:

4. If you have a "Cable Select" Ribbon, then the Jumper Connections on the Back of the CD-RW's are both set to "CSEL" Cable Select. To use "CSEL" your computer's bios MUST support CSEL.

5. I believe that "auto detect" implies you have jumpers set on CSEL and a 39 Pin CSEL Ribbon Cable.

SUGGEST YOU GO INTO YOUR BIOS AND UNSELECT AUTO DETECT AND SIMPLY ASSIGN A MASTER AND SLAVE ON WHATEVER RIBBON CABLE (THE PRIMARY OR SECONDARY) YOU HAVE THE CD-RW'S CONNECTED TO.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 12:46 AM.


Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2024, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.