MTU.Community


Go Back   MTU.Community > Microstudio Software & Burners > Microstudio Help

Microstudio Help Post Microstudio questions, tips and suggestions here.

Reply
 
Thread Tools Display Modes
  #1  
Old January 4th, 2005, 02:34 PM
silverfox1949 silverfox1949 is offline
Registered User
 
Join Date: Jul 2004
Posts: 7
712a cannot burn CD+G

I cannot get my MTU Certified px-712a usb drive to burn a CD+G. Aspi error
(04h 00h 00h) I tried the solution 1 and 2 and 3 and nothing works. Just keep getting aspi error. I have done the spyshecker .I have enough bad cd burns to decorate my walls . I have reinstalled winxp, I have reinstalled easycd/dvd creator 6. I have reinstalled microstudio. I have disabled all other cd recording software at startup and still cannot burn a cd+G or a cd for that matter. My drive is recogonized as I can insert a dvd movie or music cd and they will work. I have read the forums and don't know what else to do .
My system information is as follows. Please somebody help me.

T2085 emachine WinXP
2000 + 80GB Hard Drive 512 MB DDR
AMD Athlon xp Ultra DMA
Processor
3D S3 Graphics ProSavage 8

Drive Properties
"D"
Vendor: Sumsung
Prod ID: DVD-ROM SD-616T
Frimware Revision: F300
Address 3:0:0

"E"
Vendor: HL-DT-st
Product ID: CD_RW GCE 8400B
Firmware Revision: 1.02
Address3:1:0
Write speed 40x(6000kb/sec)
Cache Buffer 2048 KL

"F"
Plextor DVDR PX-712a External USB 2.0
Vendor: Plextor
Firm:1.05
Address:7:00

Main Chipset
VIA VT8375 (North Bridge)
Processor/Host bus support
Integrated DRAM controller
Integrated graphics AC '97 controller
3D Graphics visual enhancements
2D graphics
Arithmetic stretch blitter video
Power Management Functions

Via Vt8235 (South Bridge)
Support for PCI Interface
Integrated IDE controller
USB 2.0 and DMA controller
Power Management logic
Real-time clock
Supports AC '97 audio devices

I/O Controller
ITE IT8705FSuper I/O Controller
Floppy drive interface
One multimode parrallel port
FIFo serial port
Keyboard and mouse controller
Reply With Quote
  #2  
Old January 5th, 2005, 10:44 AM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Re: 712a cannot burn CD+G

What is the error that you are getting exactly? Have you tried connecting the drive into a different USB port? Have you tried updating the Chipset drivers for your motherboard? If not, then try these two items, it should fix it.
__________________
Bryan, MTU
Reply With Quote
  #3  
Old January 5th, 2005, 01:55 PM
silverfox1949 silverfox1949 is offline
Registered User
 
Join Date: Jul 2004
Posts: 7
Re: 712a cannot burn CD+G

I am getting error write command failed on device 2:0:0
umexpected aspi error (04h 00h 00h)
I have tried different usb port same error
I have updated my chipset drivers for the motherboard same error
Reply With Quote
  #4  
Old January 5th, 2005, 02:15 PM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Re: 712a cannot burn CD+G

See if there are any updated Drivers for the USB port on this motherboard. This problem is actually caused by the USB drivers, corrupting the data, which then gives you this error under Microstudio. Try burning under another CD burning program to see if it will burn or not.
__________________
Bryan, MTU
Reply With Quote
  #5  
Old January 5th, 2005, 05:55 PM
rhythmace rhythmace is offline
Registered User
 
Join Date: Mar 2004
Posts: 14
Smile Re: 712a cannot burn CD+G

you have to download a different aspi driver. go to nero.com and download the file to your system 32 folder. nero is the only aspi file that will work with external usb devices. I know because I had the same problem.this is how you download it. you need to save it don't try to run or open it. all you need to do is get a copy of this file on your computer into the system32 folder on your computer. do not try to run the file. to get to your system32 folder you need to go to your "my computer" then go to your "local drive c" then to the "windows" folder then you go to the "system32" folder and copy the file right in there. it may ask if you want to over write a file already there. select yes. you also have to be using windows nt, 2000, or xp. after you have done the above, open microstudio and click on drives select aspi drivers then select "use the default driver" you have to close then reopen microstudio to take effect. nero's website is "ftp://ftp6.nero.com/wnaspi32.dll" then download the file. I hope this works for you, it did for me because i also have an external usb plextor. you might also want to invest in golden hawk technology's cdrwin version 3.9c. you can extract individual tracks from a cd+g karaoke or audio cd, instead of the whole cd, and copy them to an image file in your hard drive. and it works with khp. it's great. i hope i have been some help to you.
Reply With Quote
  #6  
Old January 5th, 2005, 06:00 PM
MTUSUPPORT MTUSUPPORT is offline
Moderator
 
Join Date: Nov 2000
Location: Raleigh, NC
Posts: 5,253
Re: 712a cannot burn CD+G

Some computers just have this problem. Our ASPI Driver will actually work without any problems with any USB or Firewire device, just so you know.
__________________
Bryan, MTU
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:23 AM.


Powered by vBulletin® Version 3.7.1
Copyright ©2009 - 2025, Jelsoft Enterprises Ltd.
The contents of this forum are copyrighted by Micro Technology Unlimited, 2000-2008. Use of any material from these Forums is prohibited without written agreement from MTU.