REALLY SLOW READ times.
 

I have a new Plextor 4012a and it' taking almost 30 min to read a disk. I have tried the read at AUTO and from 24x down to 8x. All take about the same time.

SPECS: CPU is a Duron 700mh, IBM 40GIG 7200RPM Dirve, 512RAM, Direct X 8.1, clean lazer lens, 1.6GIG free disk space for BIN file, using the MTU driver, searched the forums and have EVEN read the manual.

Also, EZCD Creator 5 Plat says my drives extraction speed is 18x for audio. It reads anbd writes fine as does Nero.

Any clues at all?

Go to the drives tab, and click speed selection, put read at 40 and write at 40, I'll assume you have the 40-40 Plex. and test run it. if you get garbage on your graphics, slow down your write speed a step at a time until you are happy with what you get. If you are using 32X media you need to read at 40 and write at 32, and check for graphic garbage and slow down from that one step at a time.

Jim:w

Still REALLY slow. 1/10MG per second slow. I have even followed all the instructions on the top of the furum regarding updating to the latest drivers - no good.

Any other ideas?

Thanx!

- VP

A long shot, but you might try going to the Plextor site and dowloading any available drivers for your burner, especially any you might find regarding support for DirectX 8.1.

Good Luck,
George

George,
DURON chip?? Don't know how it works with MTU??

Vicious, what version of Micro Studio have you, and I'll assume it's the full version, not a demo.

check for firm ware upgrade on plex site.

Jim

Jim, don't see what difference the chip would make in downloading drivers from Plextor to make certain a burner supports directX 8.1

George

I have the latest version, FULL not demo. I will check on the Plex site and see if there are any options there.

Thanx for the info Gents!

- VP

slow run time and no complete import on microstudio
 

i have a plaxtor cdr i am running microstudio v2.315 and i can not import past #19/20 it stops i downloaded the aspi drivers and now it runs really slow i went to plaxtor properties and the box- auto insert notification is not checked i am running W-me i am trying to figure this out on my own over thanksgiving weekend my husband is a dj and needs his music this weekend and having a hard time getting any help i understand but please get back wit me Thank Youurgent :? :?

Vicious V,
It sounds that your problem is probably related to the Motherboard drivers. What you will need to do is either figure out what motherboard you have installed in your computer and then try to get the latest drivers for the Chipset or the EIDE controllers or both if you can find the Manufacturer of the board and model number.

If this is a prebuilt computer then please check with the manufacturer of that computer for any updates for Chipset, EIDE or INF files for that system. This is most likely what is slowing your system down.

Johnnie Jazz,
Are you duplicating the disc using Import Tracks or using the Duplicate disc tabs? If you are not able to copy the 20th track this could be that it is a Multisession disc. I need more details as to what your problems are to try to give you any more information on what to do.

I have tried both
 

i have tried to duplicate it says mulisession and import tab goes real slow and stops 3/4 of the way through song #19 out of 20i have downloaded aspi drivers thats when it started running real slow i have went into plaxtor properties and everything there is correct i called plaxtor tech support the helped me install step by step my cdr drive and program that came with it i know someone said i can't burn these cdg they are write protected i have tried 3 different ones top tunes karaoke priddis music from karaoke.com and mtv karaoke

have you tried burning a regular audio cd with the Adaptec software? Just wondering how that burner works using something besides Microstudio.

a little more info
 

i have came to the point to where now microstudio will import all but last 2 cdg'a at a good speed but the last 2 are very slow and come to a stop i was told to import seperatly but i cant import them at all very slow on last 2 songs

They were updated less then a week ago. Any other ideas!? :g

What is the Manufacturer and Disc Number you are working with?

Example: SoundChoice 8707

Are you burning to cd-r or cd-rw??

MikeP

SC mostly. Nothing over 3000 at this point ...

Fuji CD-R

NOTE: I have no problem when I import selected tracks, and then burn. That goes really well. It is ONLY on FULL disk copies ...

i think i finaly figured it out
 

i am using durabrand and verbatim CD-R's discs and i have to import the last song first then import the others i am starting to get it going i am using disc like mtv karaoke and top tunes which have a number on it TT-150 another says sterling on it and a # 28212, and #22862is another by sterling i may still have more questions later if you have any more help to offer it is greatly appreciated thank you so much for our help